So you know how to do a basic shine. But how do you get the much desired mirror shine, where you can see the world reflected in a toe cap?
Ultimately it is patience and work. The theory is no different from what was discussed in the chapter on giving a basic shine; Building up layers upon layers of polish until you have a perfectly smoothed, highly buffed surface.
However, there are many tricks and tips that will help you get there much faster.
Using the right polish.
A high gloss polish is a must for this. Ideally, one that also has a good level of hardness. The harder the polish, the harder it is to apply, but the better the end result.
Most known brands of boot polish have a specific range for high shines, such as kiwi parade gloss or saphir admiral gloss. These all have various ingredients that use more wax and fewer oils, they also tend to have high amounts of beese wax and Carnauba. Some also add silicone to artificially improve the shine. For these, it is recommended you always make sure to use a thick base coat of nourishing polish.
Of all the major brands, what I have found to be the most effective in producing a long-lasting mirror shine quickly is saphir mirror gloss. It’s expensive, but you also need to use relatively little because it builds a shine so quickly.
Layering in navy blue
A common technique is to layer in navy blue polish every couple of layers.
This is poported to add the appearance of depth to the shine by reflecting more of the blue end of the light spectrum.
Whether this is true or not hasn’t been thoroughly tested but is a popular idea among the bootblacking community, and from my own experience I do believe this to be true.
Some Bootblack’s use dark green instead of navy blue, saying it’s a better colour for adding depth. Again, this is untested and a matter of opinion. It is also far easier to find navy blue boot polish from retailers.
Using an extra fine buffing medium
The material you use to buff the polish is important. The finer the material, the smoother and easier the buff.
My personal choice is damp cotton balls. Take a cotton ball and dip it in water. Squeeze out most of the water, then tamp the damp side down into a flat surface.
Nylon tights are a common one, and also cheap and easy to obtain from most supermarket and clothes shops.
Melting the polish before application
Melting the polish before applying it to the leather is a great way to speed up the process. Applying it as a liquid means it naturally forms a smoother surface and can remove the need for buffing.
Melting the polish does have its drawbacks. It shortens the shelf life of the product. Each time it is melted more of the oils in the polish evaporate while it is heated.
For this reason, most people don’t melt a whole tin at once. Instead, they dig out a small amount with a spoon and only use what they need.
There are several ways to melt the wax:
Set it alight and extinguish.
This is the shortest of the methods. Simply touch the surface of the wax with a match or lighter and wait for the flame to spread over the top, then place the tin lid down to suffocate the flame until it is extinguished.
This is a method that is the most destructive to the polish. It rapidly burns off some of the oils, changing its composition and fills it with soot, which will dampen its shine.
The reason for doing it this way is the drama. It makes an excellent bit of theatre if you’re bootblacking publicly or using it as part of a scene.
It is advised that if you are not in these settings, then you should use a less destructive method.
Using tea light oil diffuser.
These are common and can be gotten at most bargain shops. They are made for diffusing essential oils, but work just as well for melting polish.
Dig out a portion of polish and place it in the dish at the top. Light the tea light underneath and wait for the oil to completely melt.
Using a usb Mug warmer
So this is a fun little hack that has a large benefit of not needing an open flame, thus making it much safer and more convenient to use in a club. USB mug warmers are a bit of a novelty item, and quality varies. Simply connect the USB mug warmer to a portable USB power pack, lay the (metal) tin lid on the warmer and scoop in the amount of polish you wish to melt.
When purchasing these items, make sure the mug warmer can head to at least 60-80 degrees and the USB battery pack can output at least 5V.
The technique is as follows:
- Melt the wax by your preferred method.
- Ball up your application cloth and dip it in the wax.
- Apply the wax to the leather in light but fast circles, until there is an evenly spread coating.
- Wait for the wax to cool and harden.
- Spray water over the wax
- Gently but quickly make tiny circular motions and given a bit of time this will become a smooth shine.
- Repeat until you are happy with the results.